SIIG USB 2.0 Video Capture Device Manuel d'utilisateur

(c) 2006-09, Saryna Technologies LLC/Advanced Inspection TechnologyVisualDepth for Visual Plus 3

VisualDepth for Visual Plus 310(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technology 5. Verify that the following screen appears

Installation 11(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technology5. Click Finish. 6. Repeat steps 3-5.7. You may need to restart the

VisualDepth for Visual Plus 312(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technology4. Connect the power supply (5v) to the Power In por

Installation 13(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technology2.5 Configuring SoftwareVisual Plus software connects to VisualDepth

VisualDepth for Visual Plus 314(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technology3 Using VisualDepth3.1 CalibratingVisualDepth should

Using VisualDepth 15(c) 2006-09, Saryna Technologies LLC/Advanced Inspection TechnologyPlease note that the reference gauge can be mounted to a fixed

VisualDepth for Visual Plus 316(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technology3.2.1 External PitsTo measure external pits:1. Place

Using VisualDepth 17(c) 2006-09, Saryna Technologies LLC/Advanced Inspection TechnologyMeasurements box into the Visual Inspection form.3.2.2 Internal

VisualDepth for Visual Plus 318(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technologyup any slack in the positioning cable), the probe sh

Using VisualDepth 19(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technology3.2.2.2 Removing Internal ProbeTo remove the internal probe fro

All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, ormechanical, including photocopying,

VisualDepth for Visual Plus 320(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technologythe end of the text. If the curvature of the cylinde

Using VisualDepth 21(c) 2006-09, Saryna Technologies LLC/Advanced Inspection TechnologyInspecting the angled portion of the cylinder bottomMeasurement

VisualDepth for Visual Plus 322(c) 2006-09, Saryna Technologies LLC/Advanced Inspection TechnologyInspecting cylinder sidewallMeasurement procedure (c

Using VisualDepth 23(c) 2006-09, Saryna Technologies LLC/Advanced Inspection TechnologyInspecting cylinder crownPlease note that the VisualDepth inter

VisualDepth for Visual Plus 324(c) 2006-09, Saryna Technologies LLC/Advanced Inspection TechnologyLimitations on measurement in the cylinder crown. Th

Using VisualDepth 25(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technologythose are not backing out, if they get backed out while in a cy

The manufacturer, importer, and the dealer cannot be held responsible for accidental damage, including personalinjury or any other damage, due to inap

VisualDepth for Visual Plus 34(c) 2006-09, Saryna Technologies LLC/Advanced Inspection TechnologyTable of ContentsPart IIntroduction5...

Introduction 5(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technology1 IntroductionVisualDepth for Visual Plus 3 is an accessory that allo

VisualDepth for Visual Plus 36(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technology1.3 A Few SuggestionsBefore you begin to use your Vis

Introduction 7(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technology1.6 Internal ProbeThe VisualDepth internal probe contains a spring lo

VisualDepth for Visual Plus 38(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technologybottom, sidewall or the crown the small end of the pr

Installation 9(c) 2006-09, Saryna Technologies LLC/Advanced Inspection Technology7. Once installation has been completed you will be taken to the &apo